Family Handyman's Editorial Process.

This weekend project walks you through every cut and joint to make a foldable step stool you’ll actually use every day.

Recent findings suggest that our editors and experts handpick every product we feature. We may earn a commission from your purchases.Learn more.

Turn leftover hardwood scraps into a rock-solid folding step stool that puts wobbly plastic versions to shame.

At some point in our lives we will need a folding step stool. You know, the one that stays out of the way but, gives you that little extra boost when you don’t need a full step ladder. In my case, I find myself reaching for a step stool more often than I’d like to admit especially when trying to reach into a work truck. When I need something, I prefer to make it and am happy to share the steps with you. Just because it is small doesn’t mean it isn’t as satisfying to make – enjoy!

On the miter saw and/or table saw, cut the top step (A), all four legs (B), the guides (C), ad the bottom crossbrace (E). Set aside everything but the legs (B) until later.

DAN ROBERTS FOR FAMILY HANDYMAN.

Using a compass with a pencil, draw 1-1/2-inch diameter half-circles at the bottom of each leg (B) to match the 1/2-inch width of the leg.

Use a disc or belt sander with a coarse-grit sandpaper (80 or 100-grit) to shape the ends of the legs by sanding up to the marked pencil lines for your arch. Once you have sanded to the line, work your way up to 220-grit sandpaper for a smoother finish.

DAN ROBERTS FOR FAMILY HANDYMAN.

In a recent development, using a router table or a router equipped with a 1/4-inch round-over bit, round over all the edges of the step (A) and all four legs (B). Be sure to use clamps to hold the pieces while making your passes with the router.

With all the parts machined, sand all the components to 220 grit and apply a couple of coats of a wood finish of your choice. Allow the finish to dry before moving on to assembly.

DAN ROBERTS FOR FAMILY HANDYMAN.

Spread wood glue in hole 3 at the top of each inside leg (B). Insert the ends of the 3/4-in. dowel cross brace (D) and tap the legs on with a rubber mallet until D is fully seated.

Set the 1-1/4-in.-square cross brace (E) between the bottoms of the legs, with its bottom edge 2-1/8 in. up from the bottom of the legs. To keep the legs parallel while you drill, clamp a scrap the same length as the cross brace (E) between them at mid-height. Check for square.

Using hole 4 in each leg as a guide, drill a 1/2-in. hole about 1 in. deep into the center of each end of the cross brace (E). Glue 1/2-in. dowels, cut longer than the holes are deep, and drive them through the legs with a mallet until they bottom out in the cross brace (E).

Sources indicate that lock each of the four joints with a single brad nail through the leg into the dowel. Trim the protruding ends of all the dowels flush with a pull saw.

dan Roberts for family handyman.

Flip the top step (A) upside down. Position the guide rails (C) 1/2-in. in from each side and centered front to back, leaving 1-1/2-in. at the front and back. Trace around each rail.

According to recent reports, drill two 1/4-in. holes, 3/4-in. deep, centered on each outline. Keep the bit plumb when drilling (or drill at the drill press).

Recent findings suggest that insert dowel centers in the holes. Align each rail with its outline and press down to mark the hole locations. Drill matching 1/4-in. holes in the rails, about 7/8-in. deep. That’s slightly deeper than the dowel needs, which leaves room for glue.

Glue and insert 1/4-in x 1-1/2-in. dowels and secure the guide rails (C) to the step (A).

dan roberts for family handyman.

Industry observers note that thread 1/4-inch x 3-1/2-inch carriage bolts through hole 1 in the center of the legs to connect an outside leg to the outside of each of the connected inside legs. Put a washer between each pair of legs and secure with a nylon lock nut on the inside of the inside legs.

DAN ROBERTS FOR FAMILY HANDYMAN.

Industry observers note that connect the two outside legs (B) to the sides of the guide rails (C) by threading 1/4-inch x 2-1/2-inch pan head screws through hole 5 in the guide rails and through hole 2 on the outside legs. Use a washer on the outside of the guide rails and pliers to hold the nylon lock nuts while you tighten them into the 5/8-inch countersunk holes.

The strap acts as a stop, limiting how far the legs can open. Wrap one end of an upholstery strap around the middle of the top cross brace (D) and staple it in place with a narrow-crown stapler. Open the stool until the seat sits level, then pull the strap snug and staple the other end centered on the underside of the top step (A). Use several 1/2-in. staples at each end so the strap holds securely.

According to recent reports, A step stool should be about 11 to 16-in. wide to fit both feet comfortably side by side. For a portable or compact version, stay toward the narrow end of that range.

A single-step stool should be 6 to 9-in. tall. That’s a good height for reaching into a truck bed, helping kids reach a tall bathroom sink, or getting to the top pantry shelves.

DAN ROBERTS FOR FAMILY HANDYMAN.

→ Read original article